Leave Your Message
Sliding Sleeve In Completion
Knowledge

Sliding Sleeve In Completion

2025-06-05

Sliding sleeves—sometimes called sliding side doors (SSDs) — are manipulated by wireline locks and use nipple profiles. The figure below shows a typical siding sleeve. This sleeve uses a collet to ‘hold’ the sleeve in one of three positions (open, equalizing, and closed). Sliding sleeves have earned a poor reputation – they either fail to open or close. Scale, asphaltene, solid debris, or erosion are the leading causes of these problems. Indeed, producing at high rates or through small ports can cause problems, as can trying to open or close a sleeve at high angles or with considerable differential pressures. Sliding sleeves form the basis of modern surface-controlled downhole flow control.

Typical Sliding Sleeve

Components


SSDs generally consist of a top sub, bottom sub, outer housing, and a sliding sleeve, hence, the title. There are two sets of packing at each side of the circulation holes in the outer housing, which seal off the flow path when the sleeve is in the closed position. When the sleeve moves to the open position by wireline or coiled tubing, a set of slots in the sleeve move across between the packings opposite the holes in the outer housing, hence providing a flow path.

The sleeve must be fully open before circulating; otherwise, there will be damage in the packing opposite the slots. Usually, the SSD will have an equalizing port to equalize differential pressure before the slots move past the packing.

Various models are available that open with upward or downward sleeve movement. We can install several SSDs in the completion string and selectively open or close them using the appropriate selective wireline shifting tool.

It is a must to equalize TBG and annulus pressures before opening an SSD sleeve to prevent blowing up or down the wireline tools in the tubing.

Operations


A differential pressure sufficient to overcome piston and sleeve friction is mandatory to open or close the sleeve. As the piston is balanced, the required surface pressure to open or close a valve is this pressure differential (typically a few hundred psi when new). The required pressure may increase with scale, asphaltene, or other downhole deposits. However, the force applied to open or close the sleeve can be significant (typically more than 10,000 lb), depending on the piston area. This pressure may be enough to cut through these deposits but is not guaranteed.

Applications


We generally install a sliding side door (SSD) or sliding sleeve in the tubing string during well completion. Its main application is to deliver communication between the TBG and the annulus when we choose to open. It also has other applications:

  • Kill a well before POOH with TBG during a workover operation.
  • Bring a well onto production after drilling or workover by unloading (i.e., circulating the completion fluid in the TBG out with a lighter fluid).
  • Allow selective zone production & testing in multiple zones well completion.
  • In gas lift completion.
  • Landing a blanking plug in the nipple profile to shut in well or when testing tubing.
  • Circulating inhibitors for corrosion control.
  • As a contingency to equalize pressure across a deep set of packers.

Notice


  • We should space out SSDs, and other tubing string wireline operated completion components at least 10m (30 ft) apart to prevent accidental operation of the faulty component.
  • Using an SSD above a production packer (Types of Packers) carries a risk as, historically, they have been a source of ‘A’ annulus leaks. New-generation SSDs with non-elastomeric seal technology have significantly reduced the risk of leakage, and we should now consider them more seriously for some applications.
  • Should an SSD leak, a wireline set straddle can straddle it, but this reduces full bore access for wireline operations below this depth unless we retrieve the straddle.
  • Other alternatives to SSDs have ported nipples with retrievable straddles.

As a leading manufacturer and supplier of Sliding Sleeves, Vigor possesses not only deep technical expertise in production but also unique insights into the operational demands of oil and gas extraction equipment. Drawing on extensive R&D and firsthand field experience, our engineering team delivers exceptional pre-sales technical support and solution design. We ensure you receive the optimal products and tailored solutions within the shortest possible timeframe.

If you're interested in Vigor's comprehensive range of downhole drilling, completion, and logging products, contact us today for expert product guidance and technical assistance. We look forward to connecting with you and exploring how we can support your operations.

For more information, you can write to our mailbox info@vigorpetroleum.com & marketing@vigordrilling.com